If you look closely, you’ll see rifling marks on this bullet. The same bullet that decided “Today I’m not a bullet. I think I’d rather be a squib”. .
This little fella managed to zero a stage in the rain for me today. Gun went off as usual with the same open gun loudness, but the next round was half-way out of battery. I racked that one out only to have the next round do the same thing.
A quick peek into the chamber, and there it was. .
This is my first ever squib, and it had me rattled for the rest of the match. This is a new powder/load combo for me, so I was meticulous when I loaded them. I even mic’d each round right after seating the bullet. .
I have no idea what would have caused it, but I’m exceptionally grateful that no one was hurt. .
#uspsa #pewpew #pewpewpew #racegun #speedshooting #dryfire #dryfiredaily #opengun #gunchannel #speedreloader #gunsdaily #atlasgunworks #9mm #gunsofimstagram #dailygundose #thebluebullets #montanagoldbullets
Stage 1: Brass Fest. Shooting all in one day till dusk was tough in 102 degree heat. Lucky weekend guys scored with the weather🤪 still was a terrific experience and many thanks to all the ROs that came in to help us move along. Hopefully more consistent next time. #svi #uspsa #racegun #sti #tevosports #rmrbullets #brassfest #holosun
I knew I pulled off that target 🎯 too quick and dropped a charlie. It’s like it was over there staring 👀at me when I looked back. Regardless this was a fun little QuickDraw stage from the last match.
2011 pistol build 80% day 4. More parts came in! Drilled out the hammer and sear pin holes using the Matrix Precision jig and drill bits. Finished double undercut on trigger guard (optional), I did it for comfort and control (higher purchase on the pistol). I also fit the trigger bow to move more freely within the frame. Lastly, I fit the ambidextrous thumb safety here's the pistol put together...
New slide cuts from Carver Custom. Let us know what kind of custom build you are wanting to do next!
Showing off one of our NEW slide cuts with help from @jointforceenterprises
on the cerakoting. Let us know what kind of custom build you would like us to do!
Today was the first outing for my home made laser. This is version 1.0, and it is crude. The thing worked great, and held zero perfectly. It almost worked a little too good in the shaded bays. I shot the match twice, on my second run of the classifier, I shot it all from the hip. I had a little trigger freeze. Still didn’t work out too bad. I really need to get my movement figured out before the WPA Section. I came up with a few improvements today with the laser design today hope to implement them soon. #pcc #uspsapcc #racegun #uspsa #itsafrikinlaser #drevil
Stage แรกของวันนั้น ยังไม่ตื่นดันเปลี่ยนแมก 2 รอบ | ลื่นจังหวะจะเหนี่ยวยังดีไม่ลั่น มีครบลื่น + ยิงไม่ออก + ดึงสไลด์งับลูก ทั้งหมดหายไป 7 วิ | คะแนนหายไปประมาณ 30-35 คะแนน เศร้าแท้ ดูคนอื่นยิงมีแผนดีกว่านี้ด้วย // It was first stage of the match, still not wake up, somehow changed the mag again for second time. Then the damn mud so slippery that could cause a DQ (was about to fire at that moment) then a Bullet didn’t go off, rack the slide and the bullet jam at the slide. Lost around 7 secs (about 30-35 points) What a morning 👿 29.63 secs 71.92%